How to Remove Links and Resize Your D1 Bracelet
How do you remove links from a watch?
To remove links from a watch with a pin bracelet, push the pin out of the link with a pin pusher, lift the link away, then press the pin back in to rejoin the bracelet. Take links evenly from both sides of the clasp so the case stays centered.
Every D1 Milano bracelet is joined by pins, from the Ultra Thin Bracelet to the Skeleton and Automatico bracelet models, so the steps below work across the range.
What tools do you need to remove watch links?
You need a pin pusher or a bracelet link removal tool, a small hammer or rubber mallet, a soft cloth to protect the steel, and a small dish to hold the pins. Fine tweezers help with short pins. D1 Milano also sells a Watch Strap Link Adjusting Kit.
A link removal tool holds the bracelet in a cradle and presses the pin out with a turning handle, which keeps the pressure even. A pin pusher and hammer give you more control once you have sized a bracelet before. Either way, work on the cloth so the brushed and polished surfaces stay clean.
How many links should you remove to resize a watch band?
Put the watch on, close the clasp and pinch the loose bracelet together under your wrist. The number of links you can pinch together is roughly how many to remove. To resize a watch band correctly, aim for room to slide one finger under the bracelet.
Take out one link at a time and try the watch on between each. It is quicker to take a second link out than to put one back. Wrists swell slightly through the day and in warm weather, so size the bracelet in the afternoon.
If you need to remove an odd number of links, take the extra one from one side, try the watch on, and move it across if the case sits off center.
How to remove links from a watch band, step by step
To remove links from a watch band, find the removable links, push out the pin, lift the link away and rejoin the bracelet with the same pin. The five steps below follow that order, and the same method lets you take links out of a watch on any D1 bracelet.
Step 1: Find the removable links
Turn the bracelet over and look at the side of each link. Removable links show a pin end on the side. Many pin bracelets also have small arrows on the inside of the links that show which way to push the pin. If yours has them, always push in the direction of the arrow.
The links next to the case are shaped to meet it, which is what gives an integrated bracelet its unbroken line. Leave those in place and work on the links nearer the clasp.

Step 2: Push out the pin
Set the bracelet in the link removal tool, or over the gap in a sizing block, with the pin under the pusher. Turn the handle, or tap the pusher gently with the hammer, until the pin moves. Once it is partly out, pull it free with your fingers or tweezers and put it straight into the dish.

Step 3: Remove the link
With one pin out, the link comes free at one end. Push out the pin at its other end to separate it completely. If you are removing two links, take the second from the other side of the clasp.

Step 4: Rejoin the bracelet
Line up the two ends of the bracelet so the holes meet. Push the pin back in from the side opposite to where it came out, so it sits the way it was originally fitted. Press or tap it until it is flush with the edge of the link and nothing catches when you run a finger across it.

Step 5: Check the fit
Put the watch on and close the clasp. The case should sit flat and centered, with room for one finger under the bracelet. Wipe the steel with the cloth, then keep the spare links and pins together in a small bag in the watch box. Our guide to how to clean and care for your watch covers keeping the bracelet in good condition.

How do you add links to a watch band?
To add links to a watch band, push out the pin where the link will go, set the spare link in place, then pin both of its ends into the bracelet. Use the pins you kept from the original sizing and press each one in until it sits flush.
Keep the spare links even if the fit feels right now. A bracelet sized in winter can feel tight in summer, and a watch passed to someone else may need its full length back.
What can link sizing not do?
Link sizing changes the bracelet's length one whole link at a time, so it cannot fine-tune the fit between two links. That is the trade-off for a bracelet built from individual metal links, which keeps its line unbroken. If you fall between sizes, choose the fit that sits flat without pinching.
When should you take your watch to a jeweler?
Take the watch to a jeweler if a pin will not move under steady pressure, if a pin bends, or if a link is damaged. Forcing a stuck pin can scratch the steel or bend the pin. A jeweler can size a bracelet quickly, often while you wait.
If your watch is still under warranty, contact the D1 Milano customer service team before taking it to a jeweler. They will tell you whether the repair is covered by the warranty and what to do next.
It is also the simpler route if you are sizing a watch bought as a gift and want it ready to wear on the day.
Which D1 Milano watches come on a bracelet?
D1 Milano offers bracelets across several collections, including the Ultra Thin Bracelet, the Skeleton and the Automatico. Each uses the pin system covered in this guide, so the same tools and steps apply whichever model you own or are choosing.
Read why integrated bracelet watches set the design standard, or match the case to your wrist with our guide to choosing the right watch profile for your wrist.
Browse the D1 Milano Ultra Thin bracelet watches, see the Ultra Thin Bracelet 40mm Linen, or explore the self-winding models in the men's Automatico collection.
Frequently Asked Questions
How do you take links out of a watch at home?
Push the pin out of the link with a pin pusher or a link removal tool, lift the link away, then press the pin back in to rejoin the bracelet. Work on a soft cloth, remove one link at a time, and take links evenly from both sides of the clasp.
Do D1 Milano bracelets use pins or screws?
D1 Milano bracelets use pins. Each removable link is held by a pin that you push out with a pin pusher and press back in once the bracelet is the right length. If the links have small arrows on the inside, push each pin out in the direction of the arrow.
How do I know how many links to remove from my watch?
Put the watch on, close the clasp and pinch the loose bracelet together under your wrist. The number of links you can pinch together is roughly how many to remove. Take one out at a time and try the watch on until one finger fits under the bracelet.
Can I shorten a metal watch band without a pin pusher?
You can push a pin out with a thin nail or an opened paper clip, but it is easy to slip, scratch the steel or bend the pin. A pin pusher gives you far more control. If you have no tools to hand, a jeweler can shorten the band for you.
What should I do with the links I remove?
Keep them. Store the spare links and pins together in a small bag in the watch box. Wrists change size with the seasons, and the spare links let you lengthen the bracelet later or size it for someone else.